manualshive.com logo in svg

VeEX UX400, User Manual

The VeEX UX400 user manual is available for free download from manualshive.com. This comprehensive manual provides step-by-step instructions and detailed information about operating and troubleshooting the UX400, helping users maximize their experience with this advanced product. Get your free manual today and unlock the full potential of the VeEX UX400.

Share
Download
background image

Go back to top

 

Go back to TOC

7.2.7.5 Evaluation According to ITU-T M.2100

M.2100 applies to commissioning and maintenance. Commissioning consists of a 15-minute line up phase followed by a 24-hour in-service measurement. Once the line up

phase is completed successfully, errors may occur within certain limits.

ES, SES and UAS are evaluated.

Pass/Fail results are based on threshold values S1 and S2 for ES and SES.

Settings for S1 and S2:

Path allocation: 0.1 to 100%

BISO multiplication factor: 0.1 to 100

The M.2100 evaluation can be performed on the following events:

FAS bit errors (FAS2, FAS34, and FAS140)

CRC-4 errors

EBIT errors

Bit errors (TSE)

Evaluation is made at the “Near End” and at the “Far End” for PCM-30/31 signals with CRC.

Bit errors can be evaluated for:

Unframed patterns

Framed patterns and bulk signals

N x 64kbps

Since M.2100 evaluates bit errors, facilities for evaluating block errors are disabled.

M.2100 Analysis

UX400 10G e-Manual D07-00-058P RevA00

Page 136 of 209

Summary of Contents for UX400


















































































































































































































Reviews:

No comments

Related manuals for UX400

ABB LME620-AI Service Instruction preview
LME620-AI
Brand: ABB Pages: 30
ABB LME620-AI Instructions Manual preview
LME620-AI
Brand: ABB Pages: 15
ABB PST30 Manual preview
PST30
Brand: ABB Pages: 10
ABB LME620-AI User Manual preview
LME620-AI
Brand: ABB Pages: 44
Data I/O PSV5000 Operator'S Manual preview
PSV5000
Brand: Data I/O Pages: 88
Data Aire dap4 touch Protocol Manual preview
dap4 touch
Brand: Data Aire Pages: 13
Van Air SENTINEL Installation, Operation & Maintenance Instructions preview
SENTINEL
Brand: Van Air Pages: 4
Jabra LINK 280 - User Manual preview
LINK 280 -
Brand: Jabra Pages: 8
Paradox Digiplex DGP-848 Reference And Installation Manual preview
Digiplex DGP-848
Brand: Paradox Pages: 20
Samson FOUNDATION 3730-5 Mounting And Operating Instructions preview
FOUNDATION 3730-5
Brand: Samson Pages: 132
Samson 3767 Mounting And Operating Instructions preview
3767
Brand: Samson Pages: 68
Samson 3730-2 Mounting And Operating Instructions preview
3730-2
Brand: Samson Pages: 128
Samson 3725 series Mounting And Operating Instructions preview
3725 series
Brand: Samson Pages: 68
X-POWER MULTI 1 Instruction And Installation Manual preview
MULTI 1
Brand: X-POWER Pages: 24
Samson TROVIS 3730-1 Mounting And Operating Instructions preview
TROVIS 3730-1
Brand: Samson Pages: 80
Haehne DCX Quick Start Manual preview
DCX
Brand: Haehne Pages: 44
Watts 709 Series Instruction, Installation, Maintenance And Repair Manual preview
709 Series
Brand: Watts Pages: 4
WaterCop SmartConnect Owner'S Manual preview
SmartConnect
Brand: WaterCop Pages: 4

Brands by name

Popular brands

Load more brands