VeEX UX400 User Manual Download Page 98

Page: 98 / 209

Go back to top

Go back to TOC

The

Per Stream Errors

screen displays the Current and Total error count of each stream.

Bit:

Indicates errors related to test pattern (Bit Error or LSS [Pattern Loss])

BER:

Bit Error Ratio

FCS/CRC:

Number of received frames with an invalid Frame Check Sequence (FCS)

FCS/CRC Rate
IP Checksum

(Layer 3 and 4 only)

Invalid IP Frame Check sequence

TCP/UDP Checksum

(Layer 4 only)

Jabber frames:

Number of received frames larger than 1518 bytes containing an invalid FCS

Runt frames:

Number of received frames smaller than 64 bytes containing an invalid FCS

Frame Loss
Frame Loss %
OOS

Throughtput Results - Per Stream Errors Page 1

Throughtput Results - Per Stream Errors Page 2

Go back to top

Go back to TOC

The

Per Stream Events

screen displays a Date and Time stamped record of bit errors, alarms and other anomalies pertaining to each stream.

Throughtput Results - Per Stream Events

UX400 10G e-Manual D07-00-058P RevA00

Page 98 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

VeEX UX400, User Manual, Page: 98 / 209

Search results

Summary of Contents for UX400

Reviews: