VeEX UX400 User Manual Download Page 43

Page: 43 / 209

Go back to top

Go back to TOC

MPLS Tab (Only for Layer 3 & 4):

In the MPLS tab the following parameters are configured:

MPLS label:

Configurable in the range 16 through 1,048,575 (labels 0 to 15 are reserved).

Note:

Composed of 20 bits which allows for the creation of over one million labels.

CoS:

Configurable in the range 0 to 6.

Note:

This field is three bits in length and maps directly to IP Precedence TOS bits to provide Class of Service (COS).

S-bit:

Configurable 0 or 1.

Note:

The S field is one bit in length and is used for stacking labels. This is important as it is used to indicate the last label in the label stack.

TTL:

Configurable in the range 0 to 255. The default setting is 128 hops.

Note:

Used to decrement the time-to-live counter.

BERT Setup - MPLS configuration (Layer 3 & 4)

Go back to top

Go back to TOC

IP Tab (only for Layer 3 & 4):

In the IP tab the user must configure the destination IP address and source address. The user may also configure the following IP

header fields:

IP Type:

IPv4

IP Source and IP Destination:

For IP Source, if the IP connection is up, refer to section

9.1 IP

in the

V300 Common Functions manual

. The source

address is fixed to the IP address from the IP setup menu.

IP TOS (for Quality of Service testing):

Legacy TOS or DSCP

Legacy TOS :

The first three bits of the IP TOS field can be edited:

Precedence:

000 - Routine

001 - Priority

010 - Immediate

011 - Flash

100 - Flash Override

101 - Critical

110 - Internetwork Control

111 - Network Control

TOS Values:

UX400 10G e-Manual D07-00-058P RevA00

Page 43 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands

VeEX UX400, User Manual

Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands