VeEX UX400 User Manual Download Page 129

Page: 129 / 209

Go back to top

Go back to TOC

7.2.4 Signal

The signal tab displays the Level and Frequency screen.

Page 1:

Displays

Level

measurements in electrical units (volts) for SDH and SONET, and in dBm for OTN. Loss of Signal (LOS) and the Saturation levels is shown both

graphically and in dBm.

SDH:

Measurements for STM-1, STM-4, STM-16 and STM-64 signals.

SONET:

Measurements for OC-3, OC-12, OC-48 and OC-192 signals.

OTN:

Measurements for OTU-1 and OTU-2 signals.

Signal Page 1

Page 2:

The received signal

frequency

and offset is measured and displayed.

Current:

Indicates the frequency of the input signal

Offset:

Indicates the difference between the standard rate and the rate of the input signal

Min (ppm):

Indicates the difference between the standard rate and the minimum deviation detected in the input signal

Max (ppm):

Indicates the difference between the standard rate and the maximum deviation detected in the input signal

Signal Page 2

UX400 10G e-Manual D07-00-058P RevA00

Page 129 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands

VeEX UX400, User Manual

Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands