VeEX UX400 User Manual Download Page 113

Page: 113 / 209

7.0 OTN/ SDH/ SONET (OTU2/STM-64/OC-192) Test App

Follow the steps to assign the test module to a test tab as described in

Chapter 5

of this manual.

Select the OTU2/STM-64/OC-192 Testing Application (Single or Dual Port) and click "Accept".

OTU2/STM-64/OC-192 Test App Selection

The module will be configured and the progress will be displayed on the unit's screen.

System Configuring

The OTU2/STM-64/OC-192 Testing home page will be displayed with links to Setup, Results, Alarm/Error, Profiles, SONET/SDH

Tools, PDH Tools and OTN Tools. The Test Tab in the bottom of the screen will be red in color and so will be the soft LEDs for

UX400 10G e-Manual D07-00-058P RevA00

Page 113 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

Brands by name

Popular brands

VeEX UX400, User Manual

Search results

Summary of Contents for UX400

Reviews:

Brands by name

Popular brands