manualshive.com logo in svg

VeEX UX400, User Manual, Page: 184 / 209

Share
Download
VeEX UX400 User Manual Download Page 184

J0 [RS]: Regenerator section trace

Program a 1 or 16-byte identifier to check the connection between regenerators

J1 [HP]: High order path section trace

Program a 16 or 64-byte identifier to check the high order transmission path

J2 [LP]: Low order path section trace

Program a 16 or 64-byte identifier to check the low order transmission path

Copy:

 This function allows copying the received trace identifier from RX, making it easier on the user, specially for the longer strings, to minimize typos.

Note:

 To program or edit the transmitted trace, tap the applicable trace box to display the pop-up keyboard.

TX - JO [RS]

Go back to top

 

Go back to TOC

7.5.4.2 Received Traces (RX)

J0 [RS]: Regenerator section trace

Program a 1, 16-byte or 64-byte identifier to set and check the expected trace

Enable or disable the TIM (Trace Identifier Mismatch) alarm

J1 [HP Path]: High order path section trace.

Program a 16 or 64-byte identifier to set and check the expected trace

Enable or disable the TIM (Trace Identifier Mismatch) alarm

J2 [LP Path]: Low order path section trace

Program a 16 or 64-byte identifier to set and check the expected trace

Enable or disable the TIM (Trace Identifier Mismatch) alarm

Copy:

 This function allows copying the received trace identifier from RX, making it easier on the user, specially for the longer strings, to minimize typos. It is also a quick

way to eliminate TIM alarms.

RX - JO [S]

Go back to top

 

Go back to TOC

UX400 10G e-Manual D07-00-058P RevA00

Page 184 of 209

Summary of Contents for UX400


















































































































































































































Reviews:

No comments