VeEX UX400 User Manual Download Page 165 | Manualshive

Page: 165 / 209

background image

Pointer Sequence Testing

It is recommended to run one sequence with positive adjustments followed by a sequence with

negative adjustments. Performing the measurement at the maximum positive and negative

frequency offset applicable to the line rate increases the stress on the pointer processor.

The test procedure includes an initialization period followed by a cool down period of 30

seconds with no pointer movements.

7.4.4 Trace Identifier

Tap the Trace Identifier icon to display the path trace testing screens shown below. There are dedicated tabs for Transmitted and Received (expected) path traces and

setups.

7.4.4.1 Transmitted Traces (TX)

J0 [Section]: Regenerator section trace

Program a 1 or 16-byte identifier to check the connection between regenerators

J1 [STS Path]: High order path section trace

Program a 16 or 64-byte identifier to check the high order transmission path

The message is transmitted one byte per STS-3 frame

J2 [VT Path]: Low order path section trace

Program a 16 or 64-byte identifier to check the low order transmission path

Note

: To program or edit the transmitted trace, tap the applicable trace box to display the pop-up keyboard.

Trace Identifier TX

UX400 10G e-Manual D07-00-058P RevA00

Page 165 of 209

«
...
163
164
165
166
167
...
»

Summary of Contents for UX400


















































































































































































































Reviews:

No comments

Related manuals for UX400

Brand: Bartec Pages: 26

Brand: V2 Pages: 48

Brand: Samson Pages: 32

Brand: Quantum Pages: 15

Brand: Savant Pages: 2

Brand: Belimo Pages: 2

Brand: Watts Pages: 12

Brand: Pfeiffer Vacuum Pages: 100

Brand: Hard Head Pages: 10

Brand: A10 Networks Pages: 2

Brand: Z-Wave Pages: 5

Brand: Planar Pages: 162

Brand: THK Pages: 134

Brand: J+J Pages: 56

Brand: Generac Power Systems Pages: 20

Brand: Eaton Pages: 108

Brand: Carrier Pages: 4

Brand: Allen-Bradley Pages: 139

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands