VeEX UX400 User Manual Download Page 204

Page: 204 / 209

7.8 Profiles

Profiles can be created in any application that has a "Profiles" drop-down menu available. The PDH, SDH, OTN, Ethernet and

Fiber Channel applications all have the ability to save profiles.

Profiles can be viewed and loaded in the Profiles folder located in the Files folder structure.

Accessing and Configuring Profiles

To access the Profiles menu from the

OTN/SDH/SONET

Testing main menu, tap on

Profiles

. To save a new profile select the

Save as

drop-down option. This will bring up an alphanumeric keypad to name the profile. When the profile is saved, all of the

test configurations that apply to the particular application are saved. This allows for fast access to preconfigured test

configurations.

Alphanumeric keypad

UX400 10G e-Manual D07-00-058P RevA00

Page 204 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands

VeEX UX400, User Manual

Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands