VeEX UX400 User Manual Download Page 19

Page: 19 / 209

40GE (40GBase-LR4)

100GE (100GBase-LR4)

External clock input (BNC)

Eye clock output (SMA)

SD card

40GE LR4 CFP Module

2 SMF: 1 fiber in each direction with 4x10G wavelengths

100GE LR4 CFP Module

2 SMF: 1 fiber in each direction with 4x25G wavelengths

Go back to top

Go back to TOC

4.4.2 RJ-45 Interface

Balanced, Tx and Rx electrical interfaces for T1 and E1 signals. The port is 120 ohm for E1 signals and 100 ohm for T1 signals.

Go back to top

Go back to TOC

4.4.3 Bantam Interface

Balanced, Tx and Rx interfaces for DS1 and E1 signals.

Go back to top

Go back to TOC

4.4.4 BNC Interface

Unbalanced, 75 ohm Tx and Rx interfaces for DS3 and E1, E2, E3, E4 and STM-0/STS-1 (51M), STS-3/STM-1E.

Go back to top

Go back to TOC

4.4.5 XFP/SFP Transceiver Interface

Optical Transceivers (Tx/Rx) conforming to Multi Source Agreement (MSA) recommendations are supported. Various SFPs are

available for different wavelengths and dynamic range requirements. Check the ordering options for more details. The standard

optical connector type used on SFP transceivers is LC. Please use appropriate low reflectance patchcords (Ultra Physical Contact

[UPC]) and note the damage level associated with each Transceiver. Customers opting to use or provide their own SFPs should

ensure that the transceivers are multi-rate and that digital diagnostics are supported – this enables the optical power and other

measurements when in SDH optical test mode. Furthermore, only SFPs with low jitter and good optical extinction ratio should be

used. To comply with ROHS and other local government requirements, only compliant SFP transceivers should be used.

Go back to top

Go back to TOC

4.4.6 SMA Interface

Unbalanced, NRZ electrical clock input

For DS1/T1: 1.544Mbps or 1.544 MHz

For E1: 2.048Mbps or 2.048MHz

Go back to top

Go back to TOC

4.4.7 Utility Ports

The Ethernet and USB ports are located on the top of the unit.

RJ45, 10/100/1000Base-T Port

Ethernet applications include:

IP connectivity testing

Net Wiz testing

Transfer measurement results and test profiles between the instrument and a computer using ReVeal UX400 software

UX400 10G e-Manual D07-00-058P RevA00

Page 19 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands

VeEX UX400, User Manual

Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands