manualshive.com logo in svg

VeEX UX400, User Manual

The VeEX UX400 user manual is available for free download from manualshive.com. This comprehensive manual provides step-by-step instructions and detailed information about operating and troubleshooting the UX400, helping users maximize their experience with this advanced product. Get your free manual today and unlock the full potential of the VeEX UX400.

Share
Download
background image

Power

 key: The unit is powered on and off from the red key on the keypad. The button is recessed to prevent accidental

power on. Press the key for 3-5 seconds to turn the unit on. To turn off the unit, press the Power key for at least 2

seconds. If the unit does not respond, holding the Power key down for more than 10 seconds will force the unit to switch

off.

Backlight 

key: Press the key to turn the backlight off and on. If the backlight is on a timer, the backlight will restart the

timer.

Summary

 key: Brings on a screen showing a summary of all interfaces/tests. When pressed a second time, it closes the

summary screen and returns to previous screen. This key does not interrupt operations or tests in progress.

Help

 key: Brings the user to online help, regardless of the current user interface location of the unit. When pressed a

second time, it closes the help screen. This key does not interrupt operations or tests in the progress.

File

 key: Saves test results in the unit's memory. If the measurement is still running, it will provide a snapshot the moment

the key is pressed. The Save function provides automatic storage with automatic naming and time stamping function. To

process a stored file, please go to 

7.0 Files

 in the 

V300 Common Functions manual

. Press the key again to cancel the

save operation.

Lock 

key: Can be configured to lock the keypad or capture the current screenshot.

Go back to top

 

Go back to TOC

4.2 Touch Screen Display

The LCD supports touch screen operation. To operate the touch screen to navigate the menus and tabs, use the stylus located

on the right side of the unit. Please observe the following precautions:

Never use excessive pressure on the touch screen as this may damage its functionality.

Never use sharp objects such as a pen, screwdriver, etc., as this may damage the surface.

Clean the surface of the touch screen using a soft cloth and mild detergent only. Do not use alcohol.

Go back to top

 

Go back to TOC

4.3 Battery

The UX400 chassis is equipped with an intelligent Li-ion rechargeable battery pack, which is located in the rear of the unit. The

UX400 10G e-Manual D07-00-058P RevA00

Page 14 of 209

Summary of Contents for UX400


















































































































































































































Reviews:

No comments

Related manuals for UX400

zipwake S Series Troubleshooting Manual preview
S Series
Brand: zipwake Pages: 12
Watts 7 Series Installation, Maintenance & Repair preview
7 Series
Brand: Watts Pages: 2
jbc UCR Instruction Manual preview
UCR
Brand: jbc Pages: 12
Samson 3711 Mounting And Operating Instructions preview
3711
Brand: Samson Pages: 20
praher SUPERSTAR E-3000/F2 Operating Instructions Manual preview
SUPERSTAR E-3000/F2
Brand: praher Pages: 10
IDEC HR6S-S Original Instructions Manual preview
HR6S-S
Brand: IDEC Pages: 97
HomeMatic HM-RC-12 Operating Manual preview
HM-RC-12
Brand: HomeMatic Pages: 36
Kohler DTV+ Installation And Care Manual preview
DTV+
Brand: Kohler Pages: 48
Notifier AUTOPULSE IQ-318 Manual preview
AUTOPULSE IQ-318
Brand: Notifier Pages: 62
Gecko MC-MP Service Manual preview
MC-MP
Brand: Gecko Pages: 82
DEUTSCHMANN AUTOMATION LOCON 100 Instruction Manual preview
LOCON 100
Brand: DEUTSCHMANN AUTOMATION Pages: 30
Kontron COMe-mCT10 User Manual preview
COMe-mCT10
Brand: Kontron Pages: 92
Watts AMES 660GD-15-17 Installation, Operation And Maintenance Manual preview
AMES 660GD-15-17
Brand: Watts Pages: 12
CAME BPT MTMA/08 Programming Manual preview
BPT MTMA/08
Brand: CAME Pages: 32
Quick P02 Manual Of Installation And Use preview
P02
Brand: Quick Pages: 24
SSS Siedle ECE 602-0 Product Information preview
ECE 602-0
Brand: SSS Siedle Pages: 8
Neoway N58 Hardware User'S Manual preview
N58
Brand: Neoway Pages: 87
ORTEA NEXT ICAR MCP5 Instructions Manual preview
ICAR MCP5
Brand: ORTEA NEXT Pages: 8

Brands by name

Popular brands

Load more brands