VeEX UX400 User Manual Download Page 60

Page: 60 / 209

Layer 3

MAC/IP:

Tap the MAC or IP block on the Frame image to access the setup menus.

MAC Source:

Use the default source address of the test set or configure a new or different address. See MAC address editing screen shot above.

MAC Destination

: Configure the destination MAC address of the far-end partner test set. See MAC address editing screen shot above.

Ethernet Type:

8847-MPLS unicast or 8848-MPLS multicast

RFC2544 Setup MAC Layer 3

IP:

Configure the source and destination IP addresses. The following IP header fields can be configured:

IP Type: IPv4

Source IP Address

Destination IP Address

IP TOS (for quality of service testing): Legacy TOS, DSCP

If Legacy TOS is selected, then the parameters that can be configured are: Precedence and TOS Values

If DSCP is selected, then the parameters that can be configured are: DSCP, ECT and CE

TTL

Do Not Fragment Flag: 0, 1

Protocol: 0XFF

RFC2544 IP Configuration Layer 3

UX400 10G e-Manual D07-00-058P RevA00

Page 60 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands

VeEX UX400, User Manual

Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands