VeEX UX400 User Manual Download Page 58

Page: 58 / 209

Layer 2

The following can be configured for Layer 2:

MAC:

Tap the MAC block on the Frame image to access the setup menu.

MAC Source:

Use the default source address of the test set or configure a new or different address. See MAC address editing screen shot below.

MAC Destination

: Configure the destination MAC address of the far-end partner test set. See MAC address editing screen shot below.

Ethernet Type:

Can be configured for Layer 2

RFC2544 Setup MAC Layer 2

RFC2544 MAC Editing

Data:

No payload selection is possible for Layer 2.

The payload area is populated with a VeEX signature field and other proprietary data.

RFC2544 Data Layer 2

UX400 10G e-Manual D07-00-058P RevA00

Page 58 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

Brands by name

Popular brands

VeEX UX400, User Manual

Search results

Summary of Contents for UX400

Reviews:

Brands by name

Popular brands