VeEX UX400 User Manual Download Page 143

Page: 143 / 209

7.3 Alarm / Error Injection

Alarms and Errors can be injected into different signals. At any time during the test process, tap the

Error Injection

Alarm

Injection

buttons to inject errors or generate alarms.

To access the setup for the alarms and errors, tap the button on the right side of the screen. The following buttons are there for

SDH, SONET and OTN respectively:

SDH

SONET

OTN

The type of Alarm/Error can be set by tapping the

tab.

Go back to top

Go back to TOC

7.3.1 Setup Alarm and Error Injection

The Alarm and Error screen will reflect the alarm and error types based on the test type settings selected in the Setup. For

instance the below screen shot is for SDH mode selected in Setup.

Setup Alarm and Error Injection

Go back to top

Go back to TOC

7.3.2 Alarm Generation

Generation range of different anomalies into the transmit signal. Alarm generation modes include:

Alarm Flow

Continuous:

Generates a continuous alarm when button is tapped

Count:

Specific count for 0.1s, 1s, 10s, 100s when button is tapped

Go back to top

Go back to TOC

UX400 10G e-Manual D07-00-058P RevA00

Page 143 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands

VeEX UX400, User Manual

Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands