manualshive.com logo in svg

VeEX UX400, User Manual

The VeEX UX400 user manual is available for free download from manualshive.com. This comprehensive manual provides step-by-step instructions and detailed information about operating and troubleshooting the UX400, helping users maximize their experience with this advanced product. Get your free manual today and unlock the full potential of the VeEX UX400.

Share
Download
background image

Go back to top

 

Go back to TOC

7.5.9 Round Trip Delay

The Round Trip Delay (Propagation Delay) measurement works by sending a test pattern with an error. The time it takes for the error to reach the receiver is the

propagation time through the network.

Select SDH as TX/RX standard.

View the Round Trip Delay of a looped back signal.

Set check box on Setup RX pattern to Out-of-Service.

Round Trip Delay Results

Go back to top

 

Go back to TOC

7.4.10 One Way Delay

Available with Dual Port Testing Application.

One Way Delay

UX400 10G e-Manual D07-00-058P RevA00

Page 188 of 209

Summary of Contents for UX400


















































































































































































































Reviews:

No comments

Related manuals for UX400

ABB REC650 ANSI Applications Manual preview
REC650 ANSI
Brand: ABB Pages: 370
ABB EAN823 Instructions Manual preview
EAN823
Brand: ABB Pages: 17
ABB COM600 series User Manual preview
COM600 series
Brand: ABB Pages: 104
ABB AC 800M Library Object Style Manual preview
AC 800M
Brand: ABB Pages: 120
ABB ABILITY SSC600 Product Manual preview
ABILITY SSC600
Brand: ABB Pages: 42
Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Brand: Danfoss Pages: 128
Danfoss VLT DriveMotor FCP 106 Installation Instructions preview
VLT DriveMotor FCP 106
Brand: Danfoss Pages: 4
Fagor CNC 8070 Original Instructions Manual preview
CNC 8070
Brand: Fagor Pages: 10
Fagor CNC 8070 Operating Manual preview
CNC 8070
Brand: Fagor Pages: 358
Fagor CNC 8070 Programming Manual preview
CNC 8070
Brand: Fagor Pages: 556
Fagor CNC 8060 Operating Manual preview
CNC 8060
Brand: Fagor Pages: 172
Fagor CNC 8060 Translation Of The Original Manual preview
CNC 8060
Brand: Fagor Pages: 180
Fagor CNC 8060 Hardware Configuration preview
CNC 8060
Brand: Fagor Pages: 112
FaderMate Master Control Unit Fittings Manual preview
Master Control Unit
Brand: FaderMate Pages: 36
K'Nex Education 79018 User Manual preview
79018
Brand: K'Nex Education Pages: 56
Yamaha RCX240 Supporting Supplement Manual preview
RCX240
Brand: Yamaha Pages: 92
Zamel P-258/2 Instructions Manual preview
P-258/2
Brand: Zamel Pages: 23
Zamel P-256/8 Manual Instruction preview
P-256/8
Brand: Zamel Pages: 2

Brands by name

Popular brands

Load more brands