VeEX UX400 User Manual Download Page 52

Page: 52 / 209

Go back to top

Go back to TOC

6.2.2.6 Traffic

Traffic tab:

The following Traffic statistics are displayed:

Frame type:

Test and non-test frames

Traffic type:

Layer 2 and Layer 3 Unicast, Broadcast, and Multicast frame percentage

Frame size distribution

Tap on the graph for detailed screens.

BERT Results - Traffic

Go back to top

Go back to TOC

Frames:

The following Frame distribution statistics are displayed in Count (#) and Percentage (%):

Received (RX) frames:

Total frames

Test frames

VLAN tagged frames

VLAN stacked frames

MPLS (Layer 3 and 4 only)

MPLS Stack (Layer 3 and 4 only)

Non-test frames

Transmitted (TX) frames:

Total frame - Total # frames transmitted

Pause frames:

Total number of transmitted and received Ethernet pause flow-control frames

BERT Results - Frames

UX400 10G e-Manual D07-00-058P RevA00

Page 52 of 209

Summary of Contents for UX400


















































































































































































































Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands

VeEX UX400, User Manual

Search results

Summary of Contents for UX400

Reviews:

Related manuals for UX400

Brands by name

Popular brands