manualshive.com logo in svg

Toshiba E-studio5530cPRO, Operating Instructions Manual, Page: 59 / 324

Share
Download
Toshiba E-studio5530cPRO Operating Instructions Manual Download Page 59

Interface Settings

This section describes the user tools in the Interface Settings menu under System Settings.
Default settings are shown in bold type.

Network

This section describes the user tools in the Network menu under Interface Settings.

Machine IPv4 Address

Specify the machine's IPv4 network address.
The default setting is Auto-Obtain (DHCP).
When you select [Specify], enter the IPv4 address and subnet mask as "xxx.xxx.xxx.xxx" ("x" indicates
a number).
When you select [Specify], make sure that IPv4 address is different from that of other machines on
the network.
The physical address (MAC address) also appears.

IPv4 Gateway Address

A gateway is a connection or interchange point between two networks.
Specify the gateway address for the router or host computer used as a gateway.
The default setting is 000.000.000.000.

Machine IPv6 Address

Displays the machine's IPv6 network address.

• Link-local Address

The machine's specified link-local address appears.

• Manual Configuration Address

The machine's manually configured address appears.

• Stateless Address: 1-5

The specified stateless address appears.

IPv6 Gateway Address

Displays the machine's IPv6 gateway address.

IPv6 Stateless Address Autoconfiguration

Specify IPv6 Stateless Address Autoconfiguration.
The default setting is Active.

Interface Settings

57

2

Summary of Contents for E-studio5530cPRO





































































































































































































































































































































Reviews:

No comments