Toshiba E-studio5530cPRO Operating Instructions Manual Download Page 17

Page: 17 / 324

1. Connecting the Machine

This chapter describes how to connect the machine to the network and specify the network settings.

Connecting to the Interfaces

This section explains how to identify the machine's interface and connect the machine according to the
network environment.

• A network interface cable with a ferrite core must be used for RF interference suppression.

BAX006S

1. USB2.0 port

Port for connecting the USB2.0 interface cable

2. 10BASE-T/100BASE-TX port

Port for connecting the 10BASE-T or 100BASE-TX cable

Connecting to the Ethernet Interface

This section describes how to connect Ethernet interface cable to the Ethernet interface.

• If the main power switch is on, turn it off.
• Use the following Ethernet cables.

• Unshielded Twisted Pair Cable (UTP) or Shielded Twisted Pair Cable (STP) and Category type

5 or more

Summary of Contents for E-studio5530cPRO





































































































































































































































































































































Search results

Summary of Contents for E-studio5530cPRO

Reviews:

Toshiba E-studio5530cPRO, Operating Instructions Manual, Page: 17 / 324

Search results

Summary of Contents for E-studio5530cPRO

Reviews: