Toshiba E-studio5530cPRO Operating Instructions Manual Download Page 284

Page: 284 / 324

Press [OK].

Press [Exit].

10.

Press the [User Tools/Counter] key.

Displaying Names Registered in a Group

This section describes how to display names registered in a group.
You can check the names or groups registered in each group.

Press [System Settings].

Press [Administrator Tools].

Press [Address Book: Program / Change / Delete Group].

Check that [Program / Change] is selected.

Select the group where the members you want to check is registered.

You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax
destination.

Press [Programmed User/Group].

All the names registered will be displayed.

Press [OK].

Press [Exit].

7. Registering Addresses and Users for Facsimile/Scanner Functions

282

Summary of Contents for E-studio5530cPRO





































































































































































































































































































































Search results

Summary of Contents for E-studio5530cPRO

Reviews:

Toshiba E-studio5530cPRO, Operating Instructions Manual, Page: 284 / 324

Search results

Summary of Contents for E-studio5530cPRO

Reviews: