Toshiba E-studio5530cPRO Operating Instructions Manual Download Page 25 | Manualshive

Page: 25 / 324

Toshiba E-studio5530cPRO Operating Instructions Manual Download Page 25

Menu

User Tool

Setting Requirements

File Transfer

POP3 / IMAP4 Settings

As required

File Transfer

Administrator's E-mail Address

As required

File Transfer

E-mail Communication Port

As required

File Transfer

Program / Change /
Delete E-mail Message

As required

File Transfer

Scanner Resend Interval Time

As required

File Transfer

Number of Scanner Resends

As required

• For the Effective Protocol setting, check that the protocol you want to use is set to [Active].
• When POP before SMTP is set to [On], also make settings for Reception Protocol and POP3 / IMAP4

Settings.

• When setting POP before SMTP to [On], check POP3 port number in E-mail Communication Port.

• p.57 "Interface Settings"
• p.62 "File Transfer"

Network Settings Required to Use E-mail Function

23

1

«
...
23
24
25
26
27
...
»

Summary of Contents for E-studio5530cPRO





































































































































































































































































































































Reviews:

No comments