Toshiba E-studio5530cPRO Operating Instructions Manual Download Page 288

Page: 288 / 324

Press [Address Book: Program / Change / Delete Group].

Check that [Program / Change] is selected.

Press the group key you want to change.

You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax
destination.

To change the group name and key display, press [Change] under "Group Name" or "Key
Display".

Enter the new group name or key display, and then press [OK].

To change the title, press the title key under "Select Title".

To change the registration number, press [Change] under "Registration No.".

10.

Enter the new registration number using the number keys.

11.

Press the [ ] key.

12.

Press [OK].

13.

Press [Exit].

14.

Press the [User Tools/Counter] key.

Deleting a Group

This section describes how to delete a group.

7. Registering Addresses and Users for Facsimile/Scanner Functions

286

Summary of Contents for E-studio5530cPRO





































































































































































































































































































































Search results

Summary of Contents for E-studio5530cPRO

Reviews:

Toshiba E-studio5530cPRO, Operating Instructions Manual, Page: 288 / 324

Search results

Summary of Contents for E-studio5530cPRO

Reviews: