Toshiba E-studio5530cPRO Operating Instructions Manual Download Page 250

Page: 250 / 324

• To delete the name, key display, and title, see "Deleting a Registered Name".

• p.229 "Deleting a Registered Name"

IP-Fax Destination

This section describes how to register, change, and delete an IP-Fax destination.

• For details about sending an IP-Fax, see "Sending by IP-Fax", Facsimile Reference.

Registering an IP-Fax Destination

This section describes how to register an IP-Fax Destination.

Press [System Settings].

Press [Administrator Tools].

Press [Address Book Management].

Check that [Program / Change] is selected.

Select the name whose IP-Fax destination you want to register.

Press the name key, or enter the registered number using the number keys.

Press [Fax Dest.].

7. Registering Addresses and Users for Facsimile/Scanner Functions

248

Summary of Contents for E-studio5530cPRO





































































































































































































































































































































Search results

Summary of Contents for E-studio5530cPRO

Reviews:

Toshiba E-studio5530cPRO, Operating Instructions Manual, Page: 250 / 324

Search results

Summary of Contents for E-studio5530cPRO

Reviews: