Standard Change-Makers Guardian BE Operating Instructions Manual Download Page 41

Page: 41 / 99

5.8.3

WashCard or WashCard & Datacap (non “E” versions of software)

5.8.3.1

GXP ethernet IP address

local IP address
000.000.000.000

You can set this to an address you want to use or clear it and your server will assign it (DHCP).

5.8.3.2

GXP ethernet port

local port
0

The actual port may not be important as long as it is not zero. See Appendix D Restrictions On Port
Usage.

5.8.3.3

GXP subnet mask

subnet mask
000.000.000.000

You can set this or clear it and your server will assign it.

5.8.3.4

The GXP can not get to the internet

Gateway IP address
000.000.000.000

If the router can not be found enter the IP address.

5.8.3.5

WashCard ethernet IP address

remote IP address
000.000.000.000

This is the IP address of the WashCard server and it must be set. Please contact WashCard for this
information.

5.8.3.6

WashCard ethernet port

remote port
0

This is the port used by the WashCard server and it must be set. Please contact WashCard for this
information.

5.8.3.7

Viewing error messages from the card processor

View error
message?

Press

YES

to see the message.

5.8.3.8

Warning for possible credit card problems

card usage

Summary of Contents for Guardian BE




































































































Search results

Summary of Contents for Guardian BE

Reviews:

Related manuals for Guardian BE

Brands by name

Popular brands

Standard Change-Makers Guardian BE, Operating Instructions Manual

Search results

Summary of Contents for Guardian BE

Reviews:

Related manuals for Guardian BE

Brands by name

Popular brands