Standard Change-Makers Guardian BE Operating Instructions Manual Download Page 85

Page: 85 / 99

8.1

Direct Logic 05 PLC Indicator Lights (discontinued)

XO =Wash Bay Inhibit, X1 = Proximity Sensor, X2 = Bay Fault, X3-X7 =Future expansion
YO – Y3 =Wash Selection Outputs, Y4 =not used, Y5= Bay Busy

Port / LED

XO = OFF

Wash bay empty.

XO = ON

Wash in use.

X1 = ON

Proximity sensor blocked.

X1 = OFF

Proximity sensor unblocked.

X2 = ON

Car Wash sending a fault which will shut down the Guardian XP.

X2 = OFF

Car Wash not in fault.

Y0 = ON

Wash one has been selected. On time will be set by relay on time in
wash settings menu.

Y1 = ON

Wash two has been selected. On time will be set by relay on time in
wash settings menu.

Y2= ON

Wash three has been selected. On time will be set by relay on time in
wash settings menu.

Y3= ON

Wash four has been selected. On time will be set by relay on time in
wash settings menu.

Y5 = ON

Wash bay busy or GXP waiting for end of cycle (inhibit signal).

Y5= OFF

Bay empty or GXP has received end of cycle signal.

8.2

CLICK Controller Indicator Lights

X1 =Wash Bay Inhibit, X2 = Proximity Sensor, X3 = Bay Fault, X4-X8 =Future expansion
Y1 – Y4 =Wash Selection Outputs, Y5 =not used, Y6= Bay Busy

Port / LED

X1 = OFF

Wash bay empty.

X1 = ON

Wash in use.

X2 = ON

Proximity sensor blocked.

X2 = OFF

Proximity sensor unblocked.

X3 = ON

Car Wash sending a fault which will shut down the Guardian XP.

X3 = OFF

Car Wash not in fault.

Summary of Contents for Guardian BE




































































































Search results

Summary of Contents for Guardian BE

Reviews:

Related manuals for Guardian BE

Brands by name

Popular brands

Standard Change-Makers Guardian BE, Operating Instructions Manual

Search results

Summary of Contents for Guardian BE

Reviews:

Related manuals for Guardian BE

Brands by name

Popular brands