Standard Change-Makers Guardian BE Operating Instructions Manual Download | Manualshive

Page: 45 / 99

background image

45

5.8.4.10

Troubleshooting

When connected to the WashGear card system the WashGear version will appear in the
“CONFIGURATION REPORT”. If communication is lost the version will be replaced with “not
connected”.

After initializing, the GXP will beep twice indicating that auto addressing is done. A single beep will
occur when a connection has been made to the WashGear card system.

Make sure the WashGear is selected under “CREDIT SETTINGS” and that a location id has been
entered in “OTHER SETTINGS”.

On advance replacements for the EFIII board, make sure the proper software version and board
revision is used.

What do the lights on the ethernet connector mean?

The left LED indicates a connection. It requires a loop back from the other device. In other words for
the light to be on it has to be connected at both ends.

The right LED indicates data flow. This can be just data out with no response.

1. WashGear is not selected and the cable is not connected.

No LEDs on

2. WashGear is not selected but the cable is connected.

Left LED on steady green

    When power is cycled or the Guardian is reset.
        Left LED goes off while right led blinks orange
        Then left LED is on steady green

3. WashGear is selected, the cable connected and after WashGear connection.

Left LED on
Right LED blinks green occasionally

Note:
This is the same if the WashGear application goes away.

4. WashGear selected, the cable is disconnected after WashGear connection.

Left LED off
Right LED blinks orange

«
...
43
44
45
46
47
...
»

Summary of Contents for Guardian BE




































































































Reviews:

No comments

Related manuals for Guardian BE

Brand: Quantum Pages: 4

Brand: Samson Pages: 2

Brand: Lancaster Water Treatment Pages: 12

Brand: Oasis Pages: 14

Brand: Safco Pages: 2

Brand: Sanela Pages: 9

MicroGuard Pro 2

Brand: Everpure Pages: 2

Brand: IEI Technology Pages: 66

IWCBL5OSCEC1CHBKS

Brand: Igloo Pages: 37

Brand: Kimberly-Clark PROFESSIONAL Pages: 5

avantor 612-6857

Brand: VWR Pages: 89

Brand: Oasis Pages: 6

Brand: Oasis Pages: 27

Brand: Xibu Pages: 16

Brand: Magic Chef Pages: 12

BrassMaster Plus TurfMaster

Brand: Water Control Corporation Pages: 8

FLUXPENSER XFP-01

Brand: Katanax Pages: 30

Brand: RAMTONS Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands