Standard Change-Makers Guardian BE Operating Instructions Manual Download | Manualshive

Page: 81 / 99

background image

81

limit settings for the affected device. Check the Program settings.

15-30

TRACKING CODES

– These codes are intended for use by SCM troubleshooting personnel. If code

persists, contact the nearest SCM service center.

31

DISPENSER

OUTPUT

BLOCKED

–

The dispenser (coin, bill, ticket) sensor is blocked. Check the

dispenser counting sensor and associated connections.

32

DISPENSER IS

EMPTY –

The dispenser (coin, bill, ticket) is empty. If dispenser is not empty, check the

sold out sensor connections.

33

DISPENSER IS

JAMMED –

The dispenser (coin, bill, ticket) is jammed. Check the dispense path.

34

DISPENSER HAS

OVERPAID –

The dispenser (coin, bill, ticket) has issued an extra item. Check

for debris

mixed in with the coins or bills. Debris can be counted as an extra “item”. If the error is from a ticket dispenser, check
the tickets for tears in the area around the ticket notch. Extra notches (tears) can be counted as a ticket.

35

BILL DISPENSER

COMMUNICATION

ERROR – The bill dispenser is not talking. Check the

communication (data) cable connections. Make sure the dispenser has power to it as well.

36

Not Used – Contact factory if error persists after resetting.

37

Not Used – Contact factory if error persists after resetting.

38

Not Used – Contact factory if error persists after resetting.

39

BILL DISPENSER CARTRIDGE IN

WRONG POSITION

– One of the bill cartridges in a multi-

note dispenser is in the wrong position. Check position of all bill cartridges.

7.6.1.2

Resetting Dispenser Error Conditions

You can either reset a dispenser error condition by pressing the red reset button on the dispenser
board or you can press the Machine reset button on the main control module.

Reset Button

Each dispenser is equipped with a

push button

that  can  be  used  to  reset  the  dispenser  from  an
error  condition.  It  is  only  necessary  to  reset  the
coin  dispenser  that  is  displaying  the  error  flash
code.  Allow  at  least  45  seconds  after  releasing
the  button,  for  the  entire  reset  process  to  be
completed. The flash code should change back to
the  steady  flashing  pattern  if  the  error  was
successfully reset.

Coin Dispenser w/o Door

RESET BUTTON

«
...
79
80
81
82
83
...
»

Summary of Contents for Guardian BE




































































































Reviews:

No comments

Related manuals for Guardian BE

Brand: Water Well Pages: 5

Brand: lancer Pages: 24

EFD 1500 Series

Brand: Nordson Pages: 34

Brand: Hamilton Beach Pages: 14

Brand: Perrin & Rowe Pages: 2

BOTTLE-FREE WATER DISPENSER

Brand: Permatech Pages: 17

Brand: Marlo Incorporated Pages: 52

Brand: Elson Pages: 16

Brand: Safetec Pages: 5

Brand: Master Pages: 20

SHOE COVER DISPENSER

Brand: Sterilize+ Pages: 3

Brand: Bunn Pages: 27

BUNN-O-MATIC ULTRA-1

Brand: Bunn Pages: 73

Brand: Royal Catering Pages: 9

Brand: Royal Catering Pages: 21

Brand: Aqualife Pages: 24

8HCH-KK-SSF-2/1POU

Brand: Perk Pages: 21

Brand: Polar Air Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands