Standard Change-Makers Guardian BE Operating Instructions Manual Download

Page: 86 / 99

X4 = ON

Gate closed signal return.

X4 = OFF

Gate normal.

Y1 = ON

Wash one has been selected. On time will be set by relay on time in
wash settings menu.

Y2 = ON

Wash two has been selected. On time will be set by relay on time in
wash settings menu.

Y3= ON

Wash three has been selected. On time will be set by relay on time in
wash settings menu.

Y4= ON

Wash four has been selected. On time will be set by relay on time in
wash settings menu.

Y5 = ON

Gate Open signal. On time will be set by gate rly on

Y5= OFF

time in wash settings menu.

Y6 = ON

Wash bay busy or GXP waiting for end of cycle (inhibit signal).

Y6= OFF

Bay empty or GXP has received end of cycle signal.

9.0

FREQUENTLY ASKED QUESTIONS

An owner can typically resolve many problems after he/she has been familiarized with our machine.
The following are a few examples of questions and answers you may have concerning our equipment.

What kind of car wash discounts (promotions) can I run with the Guardian XP?

The Guardian can be programmed for a time discount (early bird), or multiple coupons,

tokens, or code based discounts. See the promotion section of the Guardian Owners
Manual for more information.

Why is my bill acceptor rejecting so many bills?

Summary of Contents for Guardian BE




































































































Search results

Summary of Contents for Guardian BE

Reviews:

Related manuals for Guardian BE

Brands by name

Popular brands

Standard Change-Makers Guardian BE, Operating Instructions Manual

Search results

Summary of Contents for Guardian BE

Reviews:

Related manuals for Guardian BE

Brands by name

Popular brands