Standard Change-Makers Guardian BE Operating Instructions Manual Download Page 53

Page: 53 / 99

last address 0

This is the number of machines that are networked. Currently only two are supported. This question
is only asked if the machine is GXP 1.

5.10.22

Coin acceptor error takes the machine offline

Disable if coin
errored? NO

YES

– The machine will go offline if the coin acceptor has an error.

- The machine will continue to operate if the coin acceptor has an error.

5.10.23

Bill acceptor error takes the machine offline

Disable if bill
errored? NO

YES

– The machine will go offline if the bill acceptor has an error.

- The machine will continue to operate if the bill acceptor has an error.

5.10.24

Card system or card reader error takes the machine offline

Disable if card
errored? NO

YES

– If the machine loses communication to the card reader or if the card system has an error the

machine will go offline.

- The machine will continue to operate if the card reader or card system has an error.

5.10.25

Disable the keypad and cash voices

Disable keypad &
cash voices? YES

YES

– Disables the audio for the numeric keypad and when cash is inserted.

– The machine will say every numeric button press and for each coin and bill inserted.

5.10.26

Button Light Mode

Btn Light Mode

Flash Down

– The button lights will flash individually starting from the top selection to the

bottom selection and then repeat.

Flash Up

– The button lights will flash individually starting from the bottom selection to the top

selection and then repeat.

Flash Up Down

– The button lights will flash individually starting from the bottom selection to

top selection then back down to the bottom selection and then repeat.

Summary of Contents for Guardian BE




































































































Search results

Summary of Contents for Guardian BE

Reviews:

Related manuals for Guardian BE

Brands by name

Popular brands

Standard Change-Makers Guardian BE, Operating Instructions Manual

Search results

Summary of Contents for Guardian BE

Reviews:

Related manuals for Guardian BE

Brands by name

Popular brands