Standard Change-Makers Guardian BE Operating Instructions Manual Download Page 89 | Manualshive

Page: 89 / 99

background image

89

10.2

Coin/Token Dispenser Repair (not DLR model)

Important:

If the entire coin dispenser is replaced AND it is being replaced by one that was not the same value, it
will be necessary to check the Wash Settings in the Main Menu mode. The machine will detect the
new value and require that you check the settings before the machine can be placed into service. This
is a safety measure to ensure you have had a chance to double check your Wash Vend settings.

·

Always check the value of the coin dispenser to ensure it is the correct value for the coin you are
loading it with. For more information see the section of this manual that pertains to setting the
coin dispenser (hopper) value.

·

Be careful to avoid pinching the motor connection wires (see picture above) between the coin
dispenser control board and the coin dispenser frame.

To remove the coin dispenser with power off, disconnect all cables connections. If the dispenser will
not be replaced immediately and the dispenser is the one on the left side of the cabinet it will be
necessary to move the remaining dispenser (if present) into the left dispenser position. This is
necessary because the left dispenser is the one the bill acceptor is plugged into.

Motor Connector

Sold Out Connector

Mounting
Screw

Mounting
Screw

Mounting
Tab

Mounting
Tab

Coin
Interrupter
Optic

Coin
Interrupter
Optic

«
...
87
88
89
90
91
...
»

Summary of Contents for Guardian BE




































































































Reviews:

No comments

Related manuals for Guardian BE

Discovery DYWS4

Brand: Dacor Pages: 2

Discovery DYWS4

Brand: Dacor Pages: 12

Discovery DYWS4

Brand: Dacor Pages: 4

HVR8HD*1C Series

Brand: Halsey Taylor Pages: 7

Brand: INNOLIVING Pages: 18

Brand: U-Line Pages: 22

Brand: Sanela Pages: 6

Brand: vitapur Pages: 8

MILLENNIUM MJ30-4 PB

Brand: Cornelius Pages: 59

Brand: North Star Pages: 28

Brand: H2O International Pages: 4

Arctic Revolution 75B

Brand: AAFIRST Pages: 8

Standard Series

Brand: By The Glass Pages: 16

Brand: Halsey Taylor Pages: 8

Brand: Lancaster Pages: 14

8LDIECH-SC-WFC-SSF

Brand: Glacial Pages: 18

Brand: TCF Pages: 8

Brand: START International Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands