Standard Change-Makers Guardian BE Operating Instructions Manual Download Page 44 | Manualshive

Page: 44 / 99

background image

44

If the router can not be found enter the IP address.

5.8.4.5

WashGear ethernet IP address

remote IP address
000.000.000.000

This is the IP address of the WashGear server and it must be set. Please contact WashGear for this
information.

5.8.4.6

WashGear ethernet port

remote port
0

This is the port used by the WashGear server and it must be set. Please contact WashGear for this
information.

5.8.4.7

Viewing error messages from the card processor

View error
message?

Press

YES

to see the message.

5.8.4.8

Warning for possible credit card problems

card usage
low = 20

This is the maximum number of times cash can be used with out a credit card being used. This will
create a warning for the owner. This may indicate a card reader problem. Choose a number that fits
your cash and credit card usage.

5.8.4.9

Operating Hints

·

You will not be able to change the wash names, wash values or the clock of the GXP. This will be
done by the WashGear card system.

·

For information related to setting up and connecting to a WashGear card system, consult the
"Installation Quick Guide".

·

It may require several minutes to connect to the WashGear system. This only occurs if you cycle
power or reset the GXP.

·

If not connected or while connecting to the WashGear card system cash can still be accepted for a
wash.

·

Select the next available ”machine” number as the location ID in the Other Settings menu. Keep
in mind that you will also need to use this same location ID as the identifier when setting up the
WashGear software in the CardWorks application.

The controller in the GXP should have an EFIII board equipped with an Xport ethernet device, and
program version 3.033 or higher.

«
...
42
43
44
45
46
...
»

Summary of Contents for Guardian BE




































































































Reviews:

No comments

Related manuals for Guardian BE

Brand: EcoWater Pages: 7

Brand: Oasis Pages: 10

Brand: Oasis Pages: 2

Brand: SPM Pages: 68

Limebeater Series

Brand: LIFF Pages: 2

Brand: Kimberly-Clark Pages: 2

Brand: Galene Pages: 17

BUNN-O-MATIC ULTRA-1

Brand: Bunn Pages: 38

Brand: Bunn Pages: 62

Brand: OYPLA Home Pages: 4

BUNN-O-MATIC ULTRA-1

Brand: Bunn Pages: 73

Brand: Bunn Pages: 6

Brand: Monarch Water Pages: 8

Brand: Olympia Pages: 2

Brand: Wave Pages: 7

Brand: Yarna Pages: 8

Brand: Hague Quality Water Pages: 40

Brand: Xibu Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands