Standard Change-Makers Guardian BE Operating Instructions Manual Download Page 49 | Manualshive

Page: 49 / 99

background image

49

The

Auxiliary Alarm Relay

option can be connected to an existing dialing device that you may

already have at your site. You can set any or all of the 8 available alarm conditions to trigger the
relay, which in turn will trigger your dialer. This option is most commonly used to notify the owner
of only critical alarm conditions that have placed the machine, or wash bay, out of service.

The

Alarm Dialer

option is a dialing system that can report up to eight alarm conditions from the

machine.  The  alarm  dialer  will  call  you  and  identify  which  of  the  8  alarm  conditions  has  been
detected  thereby  allowing  you  to  determine  the  appropriate  response.  The  list  of  default  alarm
conditions available in the GXP machine is shown below. Keep in mind that the Alarm Relay differs
in that it can only signal your existing dialer that one or more of the eight alarm  conditions has been
detected, it cannot be used to identify which of the eight it was.

Below is a list of the alarm conditions that can be monitored by the machine and reported to a dialer.
See the Alarm Dialer Installation and Operating instructions for more information related to the
dialer.

·

Bill Acceptor Offline

·

Credit Card Acceptor Offline

·

Dispenser Offline

·

Cannot Make Exact Change

·

Receipt Printer Paper Empty

·

Door Opened, Note-This alarm is only available in machines equipped with the optional door
switch kit.

·

Event Report, Note-something has been added to the Event Report.

·

Machine or Wash Bay Out Of Service

5.10

Other Settings

This feature group is where all miscellaneous settings are located. Below is a list of each one.

5.10.1

Owner Language

Owner language

¬

English

®

Used to set the language used when in MAIN MENU/programming mode.

5.10.2

User 1

st

language

user 1st language

¬

English

®

This is the primary language that will be displayed to the user.

5.10.3

User 2

nd

language

user 2nd

language

¬

Spanish

®

«
...
47
48
49
50
51
...
»

Summary of Contents for Guardian BE




































































































Reviews:

No comments

Related manuals for Guardian BE

Brand: HÖR Pages: 9

600 LFCV Series

Brand: lancer Pages: 32

Brand: Comelec Pages: 4

Brand: Monument Water Systems Pages: 36

Brand: Vinotemp Pages: 20

Brand: Watts Pages: 28

INLINE CONNECT FS10

Brand: Propur Pages: 4

Brand: Bobrick Pages: 1

Brand: Bobrick Pages: 4

Brand: Bobrick Pages: 4

Brand: Cooper & Hunter Pages: 21

Cool Control Wireless 1 L

Brand: Jura Pages: 68

Brand: Yaesu Pages: 8

Brand: H2O International Pages: 21

Brand: Watts Pages: 44

Pure Water PWS10 Series

Brand: Watts Pages: 52

Brand: Oster Pages: 18

Brand: ICEE Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands