Standard Change-Makers Guardian BE Operating Instructions Manual Download

Page: 91 / 99

11.0

BILL ACCEPTORS (NOT BE OR DLR MODELS)

11.1

Bill Acceptor Preventative Maintenance

Use canned air regularly to remove dust and debris from bill path.

Use clean damp rag to wipe off optic sensors on the upper and lower track

Review OEM manufacturer’s information for additional tips.

11.2

Bill Acceptor Replacement

With power off, remove the 4 mounting nuts that hold the bill acceptor mounting plate.

Remove the bill acceptor mounting plate (4 screws) from the defective bill acceptor.

Install the mounting plate onto the replacement bill acceptor.

Install the bill acceptor / mounting plate in the machine using the 4 nuts.

11.3

MDB Bill Acceptors

The following is a list of MDB Bill Acceptors that will work in the GXP Series:
Changing bill acceptor models may require a different bill acceptor mounting bracket.

BRAND

MFG’S. PT. NO.

SCM PT. NO.

DESCRIPTION

Coinco

Vantage Series

5V00352

Coinco, Vantage, USA,$100, 700

CashCode

Currenza Series

5V00351

CashCode, Currenza, CA$100, 500

MEI

AE2602 Series

5V00219

MEI,AE2602, USA, $20, 500

MEI

AE2812 Series

5V00221-M

MEI, AE 2812, USA, $100, 500

See the bill acceptor manual for more information regarding Multi-drop Bus operation and
configuration.

Summary of Contents for Guardian BE




































































































Search results

Summary of Contents for Guardian BE

Reviews:

Related manuals for Guardian BE

Brands by name

Popular brands

Standard Change-Makers Guardian BE, Operating Instructions Manual

Search results

Summary of Contents for Guardian BE

Reviews:

Related manuals for Guardian BE

Brands by name

Popular brands