Siemens SIMOTION P Series Manual Download Page 90

Page: 90 / 138

Application planning

4.8 Mounting positions and fastening

SIMOTION P350-3 and Panels

Manual, 05/2009

4.8.6

Degree of protection

Principles

The degree of protection provided by the front side can only be guaranteed when the

mounting seal lies completely against the mounting cut-out.

CAUTION

Please ensure that the material strength at the mounting cutout does not exceed 6 mm.

Please follow the specifications for the dimensions in the "Mounting cut-out" section.
The degrees of protection are only guaranteed when the following is observed:

•

The material strength at the mounting cut-out is at least 2 mm.

•

The deviation of the evenness of the mounting cutout with an HMI device installed is

≤ 0.5 mm relative to the outside dimensions of the HMI device.

Degree of protection IP65

The IP65 degree of protection is only provided for a clamp mounting together with a ring

seal.

Degree of protection IP54

This degree of protection is provided for screw mounting.

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands