Siemens SIMOTION P Series Manual Download Page 52

Page: 52 / 138

Hardware description

3.4 IsoPROFIBUS board for SIMOTION P350-3

SIMOTION P350-3 and Panels

Manual, 05/2009

3.4.4

Technical data for the IsoPROFIBUS board

Table 3- 9

Technical data for the integrated IsoPROFIBUS board

Power consumption for + 5 V PCI voltage
Standard

2.5 W

Maximum

3.5 W

Permissible environmental conditions
Heat dissipation

Open circuit ventilation

Temperature

Operation

Storage/transport

•

IsoPROFIBUS board in SIMOTION P

5 °C to 45 °C

- 20 °C to 60 °C

Tested according to

EN 60068-2-1, EN 60068-2-2, EN 60068-2-14

Relative atmospheric humidity

Operation

Storage/transport

•

IsoPROFIBUS board in SIMOTION P

5 % … 80 %

5 % … 95 %

Tested according to

EN 60068-2-30

Temperature change

Max. 10 K per hour in operation

Moisture condensation and ice formation

Not permissible

Design
Module

Card (3.3 V/5 V, 32 bits)

Dimensions (H x D) in mm

107 x 170

Weight

150 g

Space requirements

Short PCI slot

Safety

Degree of protection

IP20 in mounted state

Protection class

I complies with VDE 0106

Safety regulations

EN 60950

Approvals

CE, UL508, cULus

Quality assurance

Quality assurance complies with ISO 9001.

Note
The safety regulations, approvals, degree of protection, and protection class specified are

only valid if the board is inserted in a SIMOTION P.

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands