Siemens SIMOTION P Series Manual Download Page 121

Page: 121 / 138

SIMOTION P350-3 and Panels
Manual, 05/2009

121

Accessories

9.1

Power supply

9.1.1

Over of power supply

An external power supply is needed to connect the SIMOTION P350-3 to the AC supply.
The power supply must provide the following values for the SIMOTION P350-3:

Output voltage:

20.4 V to 28.8 V DC, typical 24 V

Output power:

Typically 40 W (P350-3 alone), max. 130 W

Max. start-up current (for 30 ms):

14 A

Power failure buffering:

At least 3 ms with 10 s recovery time

Dynamic upper voltage limit:

30.2 V

Dynamic lower voltage limit:

18.5 V

Voltage ripple:

5 %

Note
The order numbers for and more detailed information about the accessories described can

be obtained from the online catalog which is available on the Internet at:
http://www.siemens.com/automation/mall

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands