Siemens SIMOTION P Series Manual Download Page 102

Page: 102 / 138

Connection

6.4 Connecting the (24 V) DC power supply

SIMOTION P350-3 and Panels

102

Manual, 05/2009

6.4

Connecting the (24 V) DC power supply

Note before connecting

WARNING

Only connect the device to 24 V DC power supply systems that meet the requirements of a

protective extra-low voltage (PELV); in addition, a protective conductor must be connected.

The cable cross-section must be dimensioned as appropriate for the short-circuit current of

the 24 V DC power source, so that a short-circuit will not damage the cables. Only connect

cables with a minimum cross-section of 1.3 mm

(AWG16) and a maximum cross-section of

3.3 mm

(AWG12).

NOTICE

The 24 V DC power source must be adapted to the input data of the device (see Technical

data).

Connecting

Steps for connecting the device to the 24 V power supply
1. Make sure that the On/Off switch is set to "0"

(OFF). Otherwise, the device will start up

unintentionally when the 24 V supply is

connected.

2. Switch off the 24 V DC power source.
3. Connect the DC connector.

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands