Siemens SIMOTION P Series Manual Download Page 46 | Manualshive

Page: 46 / 138

background image

Hardware description

3.3 SIMOTION P State application

SIMOTION P350-3 and Panels

46

Manual, 05/2009

3.3.2

LED display

The meaning of the LEDs and their colors is described in the table below.

Table 3- 3

Meaning of LEDs

LED

Meaning

SF (red)

This LED indicates that a fault has occurred on

SIMOTION P.

5 V DC (green)

SIMOTION P voltage on

This LED indicates that the voltage is present at P.

RUN (green) -

SIMOTION P in RUN mode

This LED indicates that the user program is running.

STOPU (yellow) -

SIMOTION P in STOP user program

mode

This LED indicates that the technology packages (for

example, synchronous operation and cam) are active.

Test and commissioning functions can be executed

without a user program. The user program is not active.

STOP (yellow) -

SIMOTION P in STOP mode

This LED indicates that no user program is running. The

technology packages are not active.

BUS1F (red) -

Group fault

This LED indicates a fault on the PROFIBUS DP

interface (X101).

BUS2F (red) -

Group fault

This LED indicates a fault on the MPI/DP interface

(X102).

3.3.3

Mode selector

The mode selector is used to set the SIMOTION P application to different states. You can

switch the control to RUN or STOP/STOPU and perform an overall reset.
A system status activated with the mode selector has priority over a status selected via

SIMOTION SCOUT. Consequently, you cannot switch the control to RUN mode via

SIMOTION SCOUT while the mode selector is set to STOP/STOPU on the

SIMOTION P350-3. You must use the mode selector for this.
Further information for the function of the mode selector switch is available in the following

documentation:
Literature:
SIMOTION P350-3 and Panel Fronts Commissioning and Hardware Installation Manual

«
...
44
45
46
47
48
...
»

Summary of Contents for SIMOTION P Series











































































































































Reviews:

No comments

Related manuals for SIMOTION P Series

Brand: Radio Shack Pages: 52

Brand: E-fly Pages: 16

Brand: S-COM Pages: 400

Brand: Fairchild Pages: 2

Brand: Fairford Pages: 233

Brand: Zeagle Pages: 37

Brand: Samson Pages: 73

coviva Smartbox TKP100A

Brand: hager Pages: 4

Brand: Vag Pages: 12

Ecomot300 AC2630

Brand: IFM Electronic Pages: 111

Brand: Lamtec Pages: 22

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: Xilinx Pages: 52

Brand: hager Pages: 2

Brand: hager Pages: 4

Brand: Jetter Pages: 24

Brand: Zaiput Flow Technologies Pages: 10

Brand: Allen-Bradley Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands