Siemens SIMOTION P Series Manual Download Page 56

Page: 56 / 138

Hardware description

3.5 MCI-PN board for SIMOTION P350-3

SIMOTION P350-3 and Panels

Manual, 05/2009

Note
The MAC address can be viewed in the device diagnostics of the SIMOTION SCOUT

Engineering System.
The IP address is set using the SIMOTION SCOUT Engineering Software (HW Config).

Label with MAC address
The MAC address of the MCI-PN board is also indicated on a label on the computing unit.

If the MCI-PN board …

then the label indicating the MAC address …

is integrated into a SIMOTION P complete

system,

already affixed underneath the rating plate on the

computing unit's housing.

has been purchased and integrated as an

optional communication module,

affixed to the module on delivery.

Pull the label off the module and stick it to the

computing unit's housing underneath the rating plate.

SYNC I/O interface X8/X9 to the IsoPROFIBUS board X4

The supplied ribbon cable (A5E00447905) is used to connect the two modules. See also

Overview of the SIMOTION P hardware installation (Page 18).

Note

•

The SYNC I/O cable MUST be plugged in when both modules (MCI-PN and

IsoPROFIBUS board) are used.

•

The enclosed battery cable does not serve any purpose when the MCI-PN is used as an

optional board (plugged into slot 2); it is not connected.

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands