Siemens SIMOTION P Series Manual Download Page 55

Page: 55 / 138

Hardware description

3.5 MCI-PN board for SIMOTION P350-3

SIMOTION P350-3 and Panels
Manual, 05/2009

3.5.3

MCI-PN board interface description

Interface overview

Table 3- 11 Interfaces of the MCI-PN board

Interface name

Connector name

Type

PROFINET

X21

4x RJ45 sockets

SYNC I/O

X8 and X9

3-pin plug connector

Backup battery

X28

2-pin plug connector

PCI bus

124-pin direct connector

(5 V/3.3 V interface)

PROFINET interface X21

The interface has 4 full-duplex 10/100 MBit Ethernet ports. The four ports are connected as

an Ethernet terminal device.

Table 3- 12 Interface features

Features

Type

Connector type

RJ45 socket connector

Cable type

Industrial Ethernet cable

Maximum cable length

100 m

Table 3- 13 X21 interface pin assignment (Port x)

Signal name

Signal type Meaning

TXP

Output

Ethernet transmit differential signal

TXN

Output

Ethernet transmit differential signal

RXP

Input

Ethernet receive differential signal

4 together with 5 via 75 ohm at the 1 nF capacitor

to the shield ground

4 together with 5 via 75 ohm at the 1 nF capacitor

to the shield ground

RXN

Input

Ethernet receive differential signal

7 together with 8 via 75 ohm at the 1 nF capacitor

to the shield ground

7 together with 8 via 75 ohm at the 1 nF capacitor

to the shield ground

Screened

backshell

M_EXT

Screen, permanently connected

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands