Siemens SIMOTION P Series Manual Download Page 38

Page: 38 / 138

Hardware description

3.2 SIMOTION P350-3 PC unit

SIMOTION P350-3 and Panels

Manual, 05/2009

3.2.5

7-segment display

The status display consists of two 7-segment displays with two 2-color LEDs.

(1)

LED H2

(2)

LED H1

(3)

2 x 7-segment display

Table 3- 1

Meaning of the 7-segment displays and LEDs

Meaning

SIMOTION operation

BIOS powering up

LED H1

no use assigned

LED H2

(next to the box label)

SIMOTION status

•

Green flashing - RUN
SIMOTION P has started up and is in

RUN mode.

•

Orange flashing - STOP
SIMOTION P has started up and is in

STOP mode.

•

Red flashing/red continuous light

- internal status

The two LEDs light up in two colors (red and

green) in order to test their operation. The two

LEDs switch off when the startup is completed

without errors.

7-segment display 1

Not currently used

(preassigned with "0")

7-segment display 2

(next to the box label)

SIMOTION status (operating status display

for SIMOTION P state)

•

6 - RUNNING
SIMOTION P has started up and the

cyclic tasks are activated.

•

0 to 5, a to f - internal status

The POST codes of the associated test step and

of the operating mode are displayed. The POST

code of the most recently started test step is

displayed when an error occurs. Code 00 is

displayed when the startup is completed without

error.

See also the SIMOTION P350-3 and Panel Fronts Commissioning Manual.

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands