Siemens SIMOTION P Series Manual Download Page 107

Page: 107 / 138

Technical specifications

7.2 Technical data for SIMOTION P350-3

SIMOTION P350-3 and Panels
Manual, 05/2009

107

Technical data

Graph
Graphics controller

Intel

Graphics memory

Graphics memory 8 MB to 128 MB SDRAM, some using

dynamic sharing of system memory

Resolutions/frequencies/colors

VGA: 1600 x 1200/32-bit color depth/85 Hz

DVI-I: 1600 x 1200/32-bit color depth/60 Hz

LCD: 1280 x 1024/18-bit

Interfaces
DVI

Port for external CRT/LCD monitor

USB

External: 4x USB 2.0 on the interface side

(max. 2 can be operated simultaneously as high current)

Onboard MPI/DP interface

- Transfer rate

- Operating mode

- Physical interface

- Memory address area

- Interrupts

9-pin SUB D socket

9.6 kBaud to 12 MBaud, parameterizable in the software

isolated:

- Data cables A, B

- Control lines RTS AS, RTS_PG

- 5 V supply voltage (max. 90 mA)

ground connection:

- DP12 connecting cable shield

RS485, isolated *

configured automatically

Ethernet

2x Ethernet interfaces (RJ45), 10/100 Mbits,

VIA MAC. VT6106S

COM1

Serial port 1

9-pin SUB D connector

CompactFlash

CompactFlash Card slot

Status displays on the device

DVD access (on drive, if installed)
2x status LEDs red/green

2x 7-segment displays for POST codes and status

Constraint affecting DVD drives: 10 Hz … 58 Hz: 0.019 mm/58 Hz to 500 Hz: 2.5 m/s

Galvanic isolation within the safety extra-low voltage circuit (SELV)

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands