Siemens SIMOTION P Series Manual Download Page 96

Page: 96 / 138

Installation/mounting

5.4 Mounting the SIMOTION panel front

SIMOTION P350-3 and Panels

Manual, 05/2009

5.4

Mounting the SIMOTION panel front

5.4.1

Overview of the mounting of SIMOTION panel fronts

With the exception of the SIMOTION P012T variant, the panels can be fastened either with

screws or with clamps. Latch fasteners have to be used for the SIMOTION P012T variant.
IP65 degree of protection can be achieved by using mounting brackets (in conjunction with a

surrounding seal).
Suspended screw mounting ensures only IP54 degree of protection.

Mounting position

The permissible mounting positions depend on the specifications of the attached computer

unit. As a unit with the SIMOTION P350-3, the SIMOTION panel front may be installed in a

vertical position with a maximum inclination of ± 20°.
Dimensioned drawings for the installation can be found in the

SIMOTION P350-3 and Panels

product manual.

5.4.2

Securing with clamps

Scope of validity

Skip this step if you have selected "fasten with screws."

Requirement

●

The mounting cut-out has been completed.

●

Clamps are readily available in the accessories. Clamp and grub screws are included in

the contents of delivery.

Figure 5-5

Clamp assembly

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands