Siemens SIMOTION P Series Manual Download Page 98

Page: 98 / 138

Installation/mounting

5.4 Mounting the SIMOTION panel front

SIMOTION P350-3 and Panels

Manual, 05/2009

Procedure

Follow the installation instructions.

Drill suitable holes at the prepared mounting cut-out in accordance with the specifications

for L4 and L5, as shown in the mounting cut-out in the dimension diagrams.

Carefully drill the respective holes into the control unit in the designated location ① from

the rear.

CAUTION

Ensure that no metal cuttings enter the device. Cover the device with film or when

drilling, use removal by suction.

Figure 5-6

Designated location for holes on the control unit

Working from the front, insert the device into the mounting cut-out.

Secure the control unit by inserting suitable screws through the holes and attaching nuts

(torque 0.4 ... 0.5 Nm).

Note
The mounting depth increases by 21 mm when an optical drive is installed in the device.
Take the dimensions from the dimensional drawings.

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands