Siemens SIMOTION P Series Manual Download Page 89

Page: 89 / 138

Application planning

4.8 Mounting positions and fastening

SIMOTION P350-3 and Panels
Manual, 05/2009

4.8.4

Permissible mounting positions of the panel front

Approval

Certain mounting positions are approved for the SIMOTION panel fronts.

Permissible mounting positions for the SIMOTION panel front

Figure 4-4

Permissible mounting position of the panel front

Vertical installation and deviations of up to 20° and – 20° in the given directions is

permissible.

Note
The mounting position illustrated has been tested and approved.

In the event of deviations from it, you might need to have additional tests carried out to verify

compliance with the general conditions applicable for the components used

(e.g. temperature). Siemens can provide appropriate support on request.

4.8.5

Type of fixation

The control unit is secured in the mounting cut-out either with clamps or screws.

NOTICE

Securing with screws is not possible with the 12" touch screen variant.

Select the mounting type suitable for your requirements for the degree of protection.

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands