Siemens SIMOTION P Series Manual Download Page 78

Page: 78 / 138

Application planning

4.1 Overview of application planning

SIMOTION P350-3 and Panels

Manual, 05/2009

General information about operation

CAUTION

The device is approved for operation in closed rooms only. The guarantee is void if this

stipulation is ignored.
Condensation

When transporting the device at low temperatures, ensure that no moisture gets on or into

the device. This also applies if the device is subjected to extreme changes in temperature.
Commissioning

Allow the device to slowly adjust to room temperature before commissioning the device. Do

not place the device near heat radiation. If condensation develops, wait 12 hours before

you switch on the device.
Vibration

DVD drives are sensitive to vibration. Inadmissible vibration during operation may result in

loss of data or damage to the drive or data medium.
Before transporting the device, wait at least 20 seconds following power off to allow the

drive to stop completely.

Avoid extreme environmental operating conditions. Protect your device against dust,

moisture and heat. For additional information, refer to the technical data.
Do not place the device in direct sunlight.

Chemical resistance

CAUTION

Adhere to the information regarding chemical resistance. Please refer to the information

available online at Address

(

http://support.automation.siemens.com/WW/view/en/16532108

Sources of light

NOTICE

Position the screen so that it is not subject to direct sunlight or other strong sources of light.

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands