Siemens SIMOTION P Series Manual Download Page 92

Page: 92 / 138

Installation/mounting

5.2 Centralized configuration

SIMOTION P350-3 and Panels

Manual, 05/2009

5.2

Centralized configuration

For a centralized structure, the SIMOTION P350-3 and the selected panel front are

connected to one another directly using guide rails and screws. Both are then installed

together in the control cabinet or controller housing.

5.2.1

Connecting the panel front to the computing unit

To connect a SIMOTION panel front to the SIMOTION P350-3, proceed as follows:
1.

Place the panel face down on a table (make sure to use a suitable surface to avoid

scratching the screen).
At the rear of the panel front, you will find 2 flat cables and one USB cable leading

through slots in the metal cover.

With the computing unit standing on its edge, slot it into the cutouts on the panel front by

the lugs on the attached guide rails (side with 7-segment display).

Connect the cables from the panel front to the interfaces on the computer unit.
–

2x flat cable

The cable grips must snap into place.

–

1x USB cable

Lower the computer onto the panel and tighten the thumbscrews on the guide rails.

&RPSXWLQJXQLW

0RXQWLQJUDLO

3DQHOIURQW

/XJV

LWV

LYH

GE\

Figure 5-1

Connection of panel front and computing unit viewed from the top

The SIMOTION panel front can now be installed in the mounting cutout.

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands