Siemens SIMOTION P Series Manual Download Page 97

Page: 97 / 138

Installation/mounting

5.4 Mounting the SIMOTION panel front

SIMOTION P350-3 and Panels
Manual, 05/2009

Procedure

Follow the installation instructions.

Working from the front, insert the device into the mounting cut-out.

Secure the device to prevent it falling out of the mounting cutout.

Hook the brackets into the designated slots on the sides of the panel fronts, matching up

the brackets with the dimensions of the mounting cutouts.

Secure the control unit in the mounting cutout from behind by tightening the grub screws

(torque 0.4 Nm to 0.5 Nm).

CAUTION

Risk of damage to the panel front
If you tighten the screws to a higher torque, this can damage the panel front (e.g. in the

form of fissures). You should, therefore, ensure strict compliance with the specified

values.

Note
The mounting depth increases by 21 mm when an optical drive is installed in the device.
Take the dimensions from the dimensional drawings.

Summary of Contents for SIMOTION P Series











































































































































Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands

Siemens SIMOTION P Series, Manual

Search results

Summary of Contents for SIMOTION P Series

Reviews:

Related manuals for SIMOTION P Series

Brands by name

Popular brands