manualshive.com logo in svg

Siemens SICAM 7KG85X, Manual, Page: 211 / 281

Share
Download
Siemens SICAM 7KG85X Manual Download Page 211

Meaning of LEDs

LEDs on the Front Side

The device automatically monitors the functions of hardware and software components. The LEDs on the front
side of the housing (see 

1.3 Device Design

) indicate the current device status.

Table 9-1

Designation of the LEDs on the Front Side

LEDs

Meaning

RUN: Device active
ERROR: Indicates an error according to parameterization
H1 to H2: According to parameterization

Depending on the status, the LEDs can be permanently on, flashing, or off. The states are described in chapter

10 Troubleshooting, Repair, and Fallback Mode

.

i

i

NOTE

The functions of the LEDs on the display side are the same as the functions of the LEDs on the top of the
housing.

LED at the Ethernet Socket

Depending on the status, the LEDs at the Ethernet socket can be permanently on, flashing, or off. The
meaning of the LEDs is explained in the following table:

Table 9-2

LEDs at the Ethernet Socket

LED

Meaning

LED Speed:

•

On: 100 Mbit/s

•

Off: 10 Mbit/s

LED Link/Activity:

•

LED on: Ethernet link is up.

•

LED flashing: Ethernet link is up and data is transferred.

•

LED off: no Ethernet partners is connected.

9.9

Commissioning and First Steps
9.9 Meaning of LEDs

210

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Reviews:

No comments