manualshive.com logo in svg

Siemens SICAM 7KG85X, Manual, Page: 45 / 281

Share
Download
Siemens SICAM 7KG85X Manual Download Page 45

Table 2-7

Settings for Time Synchronization

Parameter

Default Setting

Setting Range

Source time synchronization

Internal

Internal
Ethernet NTP
Fieldbus

Time zone offset to UTC

+00:00

-12:00 to +13:00 (hours)
(in increments of 0.5 h)

Daylight Saving Time switch-
over

Yes

No
Yes

DST offset

+01:00

0:00 to +2:00 (hours)
(in increments of 0.5 h)

Start of DST

March
Last week

January to December
First week
Second week
Third week
Fourth week
Last week

Sunday
2:00 AM

Sunday to Saturday
12:00 AM to 11:00 PM
(in increments of 1 h)

End of DST

October
Last week

January to December
First week
Second week
Third week
Fourth week
Last week

Sunday
3:00 AM

Sunday to Saturday
12:00 AM to 11:00 PM
(in increments of 1 h)

Additional Parameters if the Source is Ethernet NTP (Communication Ethernet bus protocol is set to
Modbus TCP or IEC 61850)
Primary NTP server IP Address

0.0.0.0

Any
No polling of the NTP server if 0.0.0.0 is entered

Secondary NTP server IP
Address

0.0.0.0

Any
No polling of the NTP server if 0.0.0.0 is entered

Error indication after

10 min

2 min to 120 min

Additional Parameters if Source is Fieldbus
Error indication after

10 min

2 min to 120 min

•

After the parameterization, click Send.

•

In the navigation window, click Activation and cancel.

•

Enter the activation password (refer to 

Table 2-3

).

•

Click Activation.

i

i

NOTE

NTP protocol: The SNTP client in the device is activated or deactivated during configuration of the time
synchronization. Ethernet NTP can be selected as Source time synchronization. Associated IP addresses
of the NTP servers can be entered.

Basic Functions
2.4 Time Synchronization

44

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Reviews:

No comments