manualshive.com logo in svg

Siemens SICAM 7KG85X, Manual, Page: 279 / 281

Share
Download
Siemens SICAM 7KG85X Manual Download Page 279

IED

Intelligent Electronic Device

IID

Instantiated IED Description file: It defines the configuration of one IED for a project and is used as data
exchange format from the IED configurator to the system configurator.

Indication off

Status of the indication changes from ON to OFF, that is the indication is deleted

Indication on

Status of the indication changes from OFF to ON, that is the indication is currently present

IP

Internet Protocol

IP address

Addresses in computer networks based on the Internet protocol

LED

Light-Emitting Diode

Limit violation

A value exceeding or falling under a parameterized limiting value

MBAP

Modbus Application Protocol

MBAP Header

Header of a Modbus TCP message consisting of these 4 parts: Transaction identifier (2 bytes), protocol identi-
fier (2 bytes), length (2 bytes), unit identifier (1 byte)

Modbus

The Modbus protocol is a communication protocol based on a client-server architecture.

Modbus RTU

Modbus Remote Terminal Unit: Modbus protocol type for transmitting data via serial networks (for example,
RS485)

Modbus TCP

Modbus Transmission Control Protocol: Modbus protocol type for transmitting data as TCP/IP packets;
TCP port 502 is reserved for Modbus TCP.

NTP

Network Time Protocol: Standard for synchronizing clocks in computer systems using packet-based communi-
cation networks

Power System TN

The Power transformer is neutral-point grounding and the housing of the electric equipment is protective
grounding.

Glossary

278

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Reviews:

No comments