manualshive.com logo in svg

Siemens SICAM 7KG85X, Manual, Page: 44 / 281

Share
Download
Siemens SICAM 7KG85X Manual Download Page 44

Internal Time Synchronization via RTC

Besides the external time synchronization, the internal time synchronization is also possible using the battery-
buffered RTC (Real-Time Clock). Due to the reduced accuracy, RTC should only be used in case of a failure or of
the unavailability of the external time synchronization.

Configuration via Web Pages

Configuration of the Time Synchronization

To change the time synchronization settings in the Configuration tab, proceed as follows:

•

In the navigation window, click Date and time.

[sc_admin_Time_sync, 2, en_US]

Figure 2-11

Configuration Tab, Time Synchronization

•

Configure the respective parameters according to the following table.

2.4.2

Basic Functions

2.4 Time Synchronization

SICAM, SICAM P850/P855 7KG85X, Manual

43

E50417-H1040-C482-A9, Edition 03.2022

Summary of Contents for SICAM 7KG85X


























































































































































































































































































Reviews:

No comments